TIMELESS WORK OF ART
April 3, 2025
THE AUTO BUILDER
Featured
A TRIBUTE ROADSTER
August 2, 2024
Truck Triumphs at the Triple Crown of Rodding 2023
September 13, 2023
The Best of the Best
Taking home a win at the Triple Crown of Rodding? That’s a big deal. This event isn’t your run-of-the-mill car show—it’s where the best of the best go head-to-head, and the judging is no joke. You’ve got to bring something truly exceptional, both in design and craftsmanship, to even get a nod here.
The Injection Connection
In 1999, Stotts decided to replace the carbureted 350, which was installed in 1991, with a Corvette TPI motor. Stotts wanted to bring the car into the new millennium with style, adding the extra convenience of electronic fuel injection. A resident of Mena, Arkansas, Stotts visited nearby Street & Performance to get started on his project. The S&P guys are well-known for being wizards when it comes to figuring out how to stuff an EFI motor in an older car and actually making it work.
CIMTEX RODS SUPER CAMEO: PART 2
“Building a good truck chassis is just like building the foundation for a house,” says Cimtex Rods’ Tim Cimbanin. “Everything starts at the ground floor. If you don’t have a good foundation, you don’t have anything!”
No truer words were ever spoken, and we’ve been preaching this fundamental information in all our publications.
Spotlighter
Hydro-Boost Brakes
September 27, 2022
No Comments
Nothing is more terrifying than cruising down the street to the fairgrounds when some idiot pulls out in front of you and you have to jump on the binders. Making a panic stop can be difficult when you are trying to stop 800 throbbing horsepower with a set of 9-inch rotors and single-piston calipers. You might even wonder if it will stop as you mash the brake pedal. When it comes to street rods with big motors, one braking concern is vacuum pressure. Is there enough? Many high-performance camshafts add power to the motor but produce low vacuum levels. This is something to consider when selecting your engine components. Of course, if the motor fails, you will have no vacuum, so stopping will be a real problem.
The Old EQUALIZER
April 8, 2024
No Comments
To say that the Fox-body Mustangs have been among the favorites of Ford performance enthusiasts since they began production in 1979 is like saying Henry Ford did okay. Even those without an eye for the obvious know that, by sheer numbers alone, these highly effective, as well as affordable, machines rule the streets of America. And while ’79-’93 Mustangs may lack some of the technological advancements found in Ford showrooms today, there’s an abundance of components available through the aftermarket that will make up for that shortcoming, and lots more.
LIKE A ROLLING STONE
July 16, 2023
No Comments
Bob Dillon built an F-100. Okay, so it’s not that Bob Dillon, but in this case it’s better. How, you ask? Well, there are two Bob Dillons: Bob Dillon owns this truck, but he does so with his wife, Bobbi. See, that explains it. Now let’s move on. According to the Dillons, “We did 90 percent of all the work” on the truck, and only had the guys at Cars do the final sanding, paint and assembly. The Dillons bought the 1955 Ford F-100 nearly 12 years ago and have worked at it off and on ever since. They had a definite vision for the truck, if not a timeframe, and judging from the results, it was time well spent.
Jeepspeed
February 14, 2024
No Comments
Between 1984 and 2001, Daimler Chrysler built about two million eight hundred thousand Jeep Cherokees. They were built in several combinations—two and four door, two and four wheel drive and stick or automatic and with three different engines. The vehicle was not well received. In print they were tagged as being too long, too heavy, under powered, poor brakes , and worst of all—uni-body construction. Before every Tom, Dick and Mary had an SUV in the driveway, young families were getting to work, going to school and having weekend fun. Give credit to Jeep for introducing a lot of young people to off-roading thru the Cherokee line.
Challenging The Odds
November 18, 2024
No Comments
Like old hot rods, muscle cars are getting hard to find, so as our hobby grows, different alternatives and varied approaches keep it fresh. We’ve witnessed a change in style of many of the cars being built today. No matter what the future holds, you can bet that a Mopar enthusiast will insist on having a Hemi—or another fine Mopar powerplant under the hood—whether it’s the original-style Hemi or the new, modern Hemi that’s become popular.
Extreme F-250
October 24, 2023
No Comments
Stan Belcher didn’t start out like a man possessed when he bought his ’03 Ford F-250 Super Duty Crew Cab truck. But it didn’t take long for him to turn into one. Initially, the plan was to lift the truck enough to run a set of 44-inch tires. Stan liked the Super Duty trucks because of the straight axle, which made lifting it 12 inches a snap. Three weeks later he had the body lifted three inches. He actually drove the truck with the 15-inch (total) lift and the stock wheel and 30-inch tires for about a month and a half. After installing the 44-inch tires the truck looked perfect. Everything was great, and Stan loved the truck… and then Swamper comes out with a set of 49-inch Irok tires!
Independent at Last
September 25, 2022
No Comments
“Real hot rods have axles,” or so they say. That was our story, and we stuck to it fondly for more than 10 years. The ’47 Ford sedan delivery we drive came to us with a new Super Bell dropped axle and four-bar linkage professionally installed by Dick Jones’ shop in Campbell, California. It wasn’t really a hot rod; more like a primered beater with no interior, very little glass and enough rattles that a radio was a waste of time. It was a project car for another magazine for several years, and as such was the subject of many tech articles, updating it with all manner of great stuff. But it was still a primered beater, so the axle suited it just fine, and we got many miles of enjoyment out of this setup. Oh, it could have had a nice, new IRS more than once, but it just wasn’t that kind of car.
PRODUCT SPOTLIGHT: Flaming River’s 88-98 Chevy/GMC 1500 Series Power Rack & Pinion Cradle Kit
June 25, 2024
No Comments
If you’re looking to take your 1988-1998 Chevy/GMC C1500 truck’s steering to the next level, you need to check out the Flaming River Power Rack and Pinion Cradle Kit for 88-98 Chevy/GMC 1500 series pickups. This power rack and pinion cradle kit is a total game-changer, designed for a direct bolt-in installation. Ditch that outdated steering and get ready for the precision and modern handling you’ve been dreaming of.
Junky Genie
July 11, 2024
No Comments
Have you ever seen a pictorial like this that tells where the location actually is? We didn’t think so, but don’t you just love a good mystery? Good, because that’s exactly how the owner wanted this incredible story left: unfinished. So we had to make part of it up. But which part? The interesting thing is this: Just when you think there are no old cars left to rebuild, think again!
SUBTLE CONVERSION
December 3, 2025
No Comments
If you’re searching a crowd, you’ve got to look hard, and still you might miss the builder of this astounding yet subtle Corvette. It’s almost as if the man and his cars are one and the same—loaded with talent, with their most impressive aspects available only to those who take the time to notice.
PRODUCT SPOTLIGHT: Artec Industries NEW Bantam Series Bumpers
February 21, 2024
No Comments
Artec Industries, specializing in designing and manufacturing high-quality off-road components for Jeep, Toyota, Chevy, Ford, Dodge, Scout, or Custom vehicles, is known for its innovative designs, quality reputation, fast shipping, and exceptional customer service. Founded in 2003 by Artie Nuttall, the company has a mission to provide world-class aftermarket automotive parts to off-road enthusiasts and to break the mold on what has been done in the industry. Artec’s relentless dedication ensures that it consistently exceeds customer expectations and earns their trust through unparalleled service.
From Factory to Fierce: Must-See Upgrades at the 2025 Bronco Stampede
August 21, 2025
No Comments
If your Bronco is still stock, it’s time for an upgrade. At the 2025 Great Smoky Mountain Bronco® Stampede in Pigeon Forge, the LeConte Center was transformed into a playground for anyone who refuses to settle for factory specs. First-gen classics mingled with lifted Sasquatch Editions, chopped customs, and wild builds that looked like they might break a few laws—on purpose. Every aisle was stacked with vendors showing off suspension systems, armor, lighting, audio, and off-road gear—everything needed to turn a perfectly nice stock Bronco into a beast that dominates the trail and turns heads everywhere it rolls.
